The recent progress of functionally graded CNT reinforced composites and structures

In the last decade,the functionally graded carbon nanotube reinforced composites(FG-CNTRCs)have attracted considerable interest due to their excellent mechanical properties,and the structures made of FG-CNTRCs have found broad potential applications in aerospace,civil and ocean engineering,automotive industry,and smart structures.Here we review the literature regarding the mechanical analysis of bulk CNTR nanocomposites and FG-CNTRC structures,aiming to provide a clear picture of the mechanical modeling and properties of FG-CNTRCs as well as their composite structures.The review is organized as follows:(1)a brief introduction to the functionally graded materials(FGM),CNTRCs and FG-CNTRCs;(2)a literature review of the mechanical modeling methodologies and properties of bulk CNTRCs;(3)a detailed discussion on the mechanical behaviors of FG-CNTRCs;and(4)conclusions together with a suggestion of future research trends.     

Analytical formulas for complex permittivity of periodic composites. Estimation of gain and loss enhancement in active and passive composites

ABSTRACT

The asymptotic homogenization method is applied to complex dielectric periodic composites. An equivalence to coupled dielectric problems with real coefficients is shown. This is similar to a piezoelectric problem: an out-plane mechanical displacement and an in-plane electric potential establishing a correspondence principle. Closed-form formulas for the complex dielectric effective tensor in the case of a square array of circular inclusions embedded in a matrix are given. These formulas are written in terms of a real and symmetric matrix which facilitates the implementation of the computational scheme. We also get similar formulas for multilayered complex dielectric composites. The real closed-form formulas are advantageous for estimating gain and loss enhancement properties of active and passive composites in certain volume fraction intervals. Numerical computations are performed and the results are compared with other approaches showing the usefulness of the obtained formulas. This may be of interest in the context of metamaterials.     

Catechol‐Functionalized Polyolefins

The incorporation of comonomers during ethylene polymerization can efficiently modulate important material properties of the polyolefins. Utilizing bioresourced comonomers for the generation of high‐performance polyolefin materials is attractive from a sustainability point of view. In this contribution, bioresourced eugenol and related comonomers were incorporated into polyolefins through palladium‐catalyzed copolymerization and terpolymerization reactions. Importantly, high‐molecular‐weight catechol‐functionalized polyolefins can be generated. The introduction of different metal ions induces efficient interactions with the incorporated catechol groups, leading to enhanced mechanical properties and self‐healing properties. Moreover, the catechol functionality can greatly improve other properties such as surface properties, adhesion properties, and compatibilizing properties. The catechol‐functionalized polyolefin was demonstrated as a versatile platform polymer for accessing various materials with dramatically different properties.     

An Insight into the Diffusion of Unsaturated Polyester (UP) Resin into Expanded Graphite (EG) to Improve the Mechanical Properties of the UP/EG Composites

Abstract

Polymer/expanded graphite (EG) nanocomposites have great importance in many industrial applications mainly due to their high electrical/thermal conductivity or flame retardancy. However, to fully employ the benefits of polymer/EG nanocomposites one must consider the high degree of porosity of EG. The high degree of porosity of EG can deteriorate the composites’ mechanical properties if the polymer chains cannot diffuse completely into the EG pores. In this article, an insight is given into the diffusion of unsaturated isophthalic polyester (UP) resin, consisting of a combination of maleic anhydride and isophthalic anhydride in the resin backbone, with two viscosities, into the pores of the EG particles of various degrees of porosity. The diffusion experiments were carried out on compressed EG tablets with the same density but different porosity due to the different porosity of the EG particles. The results showed that the diffusion rate of the UP resin with higher viscosity slightly decreased when the EG porosity decreased but, in the opposite way, it strongly increased for the low viscosity UP resin. The EG nanocomposites samples were molded at varying pressures. The micrographs of the fractured surfaces of the EG nanocomposites showed that the EG pores were not filled with resin, thus the EG nanocomposites had residual pores. It was found that composites containing EGs with higher expansion ratio and larger particles and pores showed larger residual pores. Furthermore, the composites prepared with the more viscous UP resin showed more residual pores. By applying a pressure of 10?bar instead of 1?bar, a reduction of 7–20% in the residual pores of the nanocomposites was observed which led to improved mechanical properties by up to 20% in flexural strength for the EG with the highest expansion ratio.     

基于三维荧光光谱法和PARAFAC对多环芳烃定性定量分析

三维荧光光谱法在研究多环芳烃(PAHs)类物质的荧光信息时起到了重要作用。多环芳烃类物质具有致癌性,难降解性,多由尾气排放,垃圾焚烧产生,危害着人类健康及环境,因此人们不断探索对多环芳烃检测的方法。实验选取多环芳烃中的苊和萘作为检测物质,利用FLS920荧光光谱仪,为避免荧光光谱仪本身产生的瑞利散射影响,设置起始的发射波长滞后激发波长40 nm,设置扫描的激发波长(λex)范围为:200~370 nm,发射波长(λem)范围为:240~390 nm,对多环芳烃进行荧光扫描获取荧光数据,采用三维荧光光谱技术结合平行因子算法对混合溶液中的苊和萘进行定性定量分析。实验选用的苊和萘均购于阿拉丁试剂官网,配制浓度为10 mg·L-1的一级储备液,再将一级储备液稀释,得到苊和萘浓度为0.5,1,1.5,2,2.5,3,3.5,4和4.5 mg·L-1的二级储备液,并将苊和萘进行混合。在进行光谱分析前需要对苊和萘的光谱进行预处理,采用空白扣除法扣除拉曼散射的影响,并采用集合经验模态分解(EEMD)消除干扰噪声。实验测得苊存在两个波峰,位于λex=298 nm,λem=324/338 nm处,萘存在一个波峰,位于λex=280 nm,λem=322 nm处。选用的PARAFAC算法对组分数的的选择很敏感,因此采用核一致诊断法预估组分数,估计值2和3的核一致值都在60%以上,分别对混合样品进行了2因子和3因子的PARAFAC分解,将分解后得到的激发发射光谱数据和各组分浓度数据进行归一化处理,并绘制光谱图,与归一化处理后的真实的激发发射光谱图和各组分浓度图进行对比。同时将PARAFAC得到的混合样本的预测浓度,通过计算回收率(R)和均方根误差(RMSEP)来判定定量分析的准确度。选择2因子时,各混合样品中苊和萘拟合度为95.7%和96.7%,平均回收率分别为101.8%和98.9%,均方根误差分别为0.0187和0.0316;选择3因子时,各混合样品中苊和萘拟合度为95.3%和95.8%,平均回收率分别为97%和102.5%,均方根误差分别为0.033和0.116,由三项指标可得选用2因子进行定性定量分析的效果明显好于选用3因子。分析实验结果表明,基于三维荧光光谱法和PARAFAC算法对混合样品进行定性定量分析,能够有效的判定混合样品的类别,同时能够成功的预测出混合样品的浓度。     

Ti0.33WO3电子结构和太阳辐射屏蔽性能第一性原理研究

节能减排已成为当今社会发展的主题,对节约能源、提高太阳能的高效综合利用的新型窗用透明隔热材料的理论设计和研究尤其重要.本文采用基于密度泛函理论的计算方法,研究了六方相三氧化钨Ti掺杂前、后的晶格参数、电子能带结构、形成能和光学性质.研究结果表明,Ti掺杂后晶格体积增大,系统能量降为负值,体系具有更好的稳定性;掺杂后电子能带结构发生很大的变化,但材料仍保持n型电导率;随之,其光学性质也发生改变,掺杂前h-WO3无近红外吸收性能,掺杂后的Ti0.33WO3具有很强的近红外吸收性能.在此基础上研究了Ti掺杂h-WO3前、后的太阳辐射屏蔽性能,掺杂前无太阳辐射屏蔽性能;掺杂后的Ti0.33WO3薄膜具有可见光高透明、近红外屏蔽的性能.计算结果为Ti掺杂h-WO3在窗用透明隔热材料方面的研究提供了理论依据.     

基于化学学科认知障碍突破的中考复习教学实践* ——以“二氧化碳的性质”为例

分析学生对二氧化碳的3个典型学科认知障碍,以“二氧化碳的捕捉”为情境,通过“尝试捕捉二氧化碳”“谁在捕捉二氧化碳”“捕捉背后的原理”等3个主要环节,实现对学科认知障碍的突破,展示了一种新的中考复习教学思路。     

电镀铜实验中镀层性质及其影响因素的探究*

电镀实验是电解原理应用的重要案例,通过实验不仅要获得定性的感性认知,还应该获得定量的理性数据。针对电镀铜实验,通过改变铜离子浓度、pH、电解时间、电解电压和电解温度等因素,探究其对镀层厚度、均匀性和致密性等性质的影响,在电解原理的基础上分析其形成机制,从而确定了电镀铜较适宜的操作条件,以此为学生开展电镀实验提供参考案例与研究思路。     

A Comparative Study of the Semiconductor Behavior of Organic Thin Films: TCNQ-Doped Cobalt Phthalocyanine and Cobalt Octaethylporphyrin

The structure formed by cobalt phthalocyanine (CoPc) and cobalt octaethylporphyrin (CoOEP) with electron-acceptor tetracyano-π-quinodimethane (TCNQ), was studied by Density Functional Theory (DFT) methods. According to theoretical calculations, both cobalt systems can establish dispersion forces related to TCNQ and also in both cases the link between them is built by means of hydrogen bonds. Based on the results of these DFT calculations, we developed experimental work: the organic semiconductors were doped, and the thermal evaporation technique was used to prepare semiconductor thin films of such compounds. The structure of the films was studied by FTIR and Raman spectroscopy. The optical properties of the CoPc-TCNQ and CoOEP-TCNQ films were investigated by means of UV-Vis measurements. The results obtained were used to estimate the type of transitions and the optical bandgap. The results were compared to the previously calculated theoretical bandgap. The CoOEP-TCNQ film presented the smallest theoretical and experimental bandgap. Finally, the electrical properties of the organic semiconductors were evaluated from a PET (polyethylene terephthalate)/indium tin oxide (ITO)/cobalt macrocycle-TCNQ/silver (Ag) device we prepared. The CoOEP-TCNQ-based device showed an ohmic behavior. The device manufactured from CoPc-TCNQ also showed an ohmic behavior at low voltages, but significantly changed to SCLC (space-charge limited conductivity) at high voltage values.     

Microstructure and Thermal and Tensile Properties of Poly(vinyl alcohol) Nanocomposite Films Reinforced by Polyacrylamide Grafted Cellulose Nanocrystals

Abstract

Polyacrylamide grafted cellulose nanocrystals (CNC-g-PAM) were incorporated into poly(vinyl alcohol) (PVA) by a solution casting method to fabricate nanocomposite films with enhanced thermal and tensile properties. The microstructure and the thermal and tensile properties of the PVA/CNC-g-PAM nanocomposite films were investigated as a function of CNC-g-PAM content. Infrared spectroscopy corroborated the presence of hydrogen bonds between PVA and the PAM on the surface of the CNC. Polarized optical microscopy and scanning electron microscopy revealed good dispersion of the CNC-g-PAM in the PVA matrix and good interfacial compatibility. Accordingly, the initial degradation temperature of the nanocomposite films was elevated slightly compared to pristine PVA film. The glass transition temperature, melting temperature, and crystallinity of the PVA also varied slightly after the incorporation of the CNC-g-PAM. At both 0% and 50% RH, the nanocomposite films showed an obvious increase of elastic modulus, no apparent change of breaking strength and a drastic reduction of elongation at break with increasing CNC-g-PAM content.